Characteristics
Vertical
System
|
|
CSA7404B
|
|
Input Channels
|
4*1
|
|
Hardware Analog Bandwidth (-3 dB)
|
4 GHz
|
|
Rise Time 10% to 90% (Typical)
|
100 ps
|
|
Rise Time 20% to 80% (Typical)
|
72 ps
|
|
Input Coupling
|
DC, GND
|
|
Input Impedance
|
50 Ω
|
|
Input Sensitivity
|
2 mV/div to 1 V/div
|
|
Vertical Resolution
|
8 bits, (>11 bits with averaging)
|
|
Max. Input Voltage
|
<1 VRMS for <100 mV/div, <5 VRMS for
≥100 mV/div settings. Also determined by TekConnect® accessory
|
|
Offset Range
|
2 mV to 50 mV/div ±0.5 V, 50.5 mV to 99.5 mV ±0.25 V, 100 mV to
500 mV ±5 V, 505 mV to 1 V/div ±2.5 V
|
|
DC Gain Accuracy 4 mV/div to 1 V/div
|
±(2% + (2% x net offset/10)) net offset = voltage level at center
screen (vertically)
|
*1 At ≥10 mV/div.
Optoelectronic System
|
|
CSA7404B
|
|
Specifications assume use of the included 013-0327-00
O-to-E Output to CH1 interconnect (unless otherwise noted).
|
|
Optical channel unfiltered bandwidth
|
2.4 GHz
|
|
Input Connector
|
Rifocs universal connector
|
|
Wavelength range
|
700 nm to 1650 nm
|
|
Calibrated wavelengths
|
780 nm, 850 nm, 1310 nm, 1550 nm
|
|
O/E Gain
|
≥0.27 V/mW (0.35 V/mW typical) @ 780 nm ±20 nm
≥0.33 V/mW (0.40 V/mW
typical) @ 850 nm ±20 nm
≥0.64 V/mW (0.75 V/mW typical) @ 1310 nm ±20 nm
≥0.64 V/mW
(0.75 V/mW typical) @ 1550 nm ±20 nm
|
|
Sensitivity (smallest average power for mask test). Assumes scale
factor is set to minimum μW/div settings and signal is at least 4 divisionsp-p
|
40 μWp-p at 1310 nm and 1550 nm. 20 μW (-17 dBm) average
power assuming 50% average duty cycle
80 μWp-p at 780 nm
and 850 nm. 40 μW (-14 dBm) average power assuming 50% average duty cycle
|
|
RMS Noise
|
≤1.1 μW + (6.5% of W/div setting) at 1310 nm and 1550 nm
≤2.1 μW
+ (6.5% of W/div setting) at 850 nm
≤2.6 μW + (6.5% of W/div setting)
at 780 nm
|
|
Input range
|
10 μW/div to 500 uW/div
Optical reference receiver typically
available over the following range: 40 μW (-14 dBm) to 400 μW (-4 dBm) at
wavelength <1200 nm; 25 μW (-16 dBm) to 250 μW (-6 dBm) at wavelength >1200
nm.
|
|
Absolute Maximum Nondestructive Optical Input
|
5 mW average; 10 mW peak at wavelength with highest relative responsivity
|
|
Maximum Nonsaturating Linear Response to Transient Input (Typical)
|
<170 μW average input (340 μW pk) at 850 nm <120 μW average
input (240 μW pk) at 1310 and 1550 nm
|
|
Fiber Input
|
62.5 μm core multimode fiber
|
|
Input Return Loss (typical)
|
With 50 μm or 62.5 μm core multimode fiber (CPC6) attached:
>14 dB
for 780 nm ±20 nm
>14 dB for 850 nm ±20 nm
With 9 μm core single
mode fiber (SMF-28) attached:
>28 dB for 1310 nm ±20 nm
>28 dB
for 1550 nm ±20 nm
|
Optical Reference Receiver System
|
|
CSA7404B
|
|
Fourth-order Bessel-Thompson filter response at the following
rates:
|
|
SONET/SDH
|
OC-1/STM0 (51.84 Mb/s)
OC-3/STM1 (155.52 Mb/s)
OC-12/STM4
(622.08 Mb/s)
OC-48/STM16 (2488.3 Mb/s)
OC-48 FEC (2.666 Gb/s)
|
|
Gigabit Ethernet
|
1000Base SX (1.25 Gb/s)
1000Base LX (1.25 Gb/s)
|
|
Fibre Channel
|
FC133 (132.7 Mb/s)
FC266 (265.6 Mb/s)
FC531 (531.2 Mb/s)
FC1063
(1063.5 Mb/s)
FC2125 (2127 Mb/s)
|
|
IEEE 1394b
|
S400 (491.5 Mb/s)
S800 (983.04 Mb/s)
S1600 (1.9661 Gb/s)
|
|
InfiniBand
|
2.5 Gb/s (2127 Mb/s)
|
|
VSR
|
1.24416 Gb/s
|
Clock Recovery System
|
|
CSA7404B
|
|
Clock Recovery Phase Locked Loop Bandwidth
|
Fbaud/1600 typical
|
|
Tracking/Acquisition Range
|
±2% of requested baud
|
|
Clock Recovery Jitter (Typical)
|
<0.25% bit period +5 psRMS for PRBS data pattern or
4 psRMS for repeating “011” data patterns
|
|
Input Sensitivity for Clock Recovery
|
1 division pk-pk displayed signal
|
|
Input Data Rates
|
1.5 Mbaud to 3.125 Gbaud
|
Communications Mask Testing
|
|
CSA7404B
|
|
SONET/SDH GR 253-CORE (Issue 39/21/2000)
|
OC-1/STM0
OC-3/STM1
OC-12/STM4
OC-48/STM16
OC-48
FEC (2.666 Gb/s)
|
|
ITU-T G.703 (10/98)
|
DS1 Rate, DS2 Rate Sym Pair, DS2 Rate Coax, DS3 Rate E1 Sym Pair,
E1 Coax, E2, E3 E4 Binary 0, E4 Binary 1 32 Mb, 97 Mb STM 1E 0/Bin 0, STM
1E 1/Bin 1
|
|
ANSI T1.102-1993 (R1999)
|
DS1, DS1A, DS1C, DS2, DS3, DS4NA, DS4NA Max Output STS-1 Pulse, STS-1
Eye STS-3, STS-3 Max Output
|
|
Ethernet IEEE Std 802.3 and ANSI X3.263-1995
|
100 Base-T STP, 100 Base-T UTP
1000 Base-SX Short Wave Optical
1000
Base-LX Long Wave Optical
1000 Base-CX
|
|
Fibre Channel Optical (ANSI X3.303-1997)
|
FC133, FC266, FC531, FC1063, FC1063 Draft Rev 11 FC2125 Draft Rev
11
|
|
Fibre Channel Electrical (ANSI X3.303-1997)
|
FC133E, FC266E, FC531E, FC1063E, FC1063E Normalized Beta, Delta, Gamma
Transmit FC1063E Absolute Beta, Delta, Gamma Transmit FC1063E Absolute Beta,
Delta, Gamma Receive, FC2125E Normalized Beta, Delta, Gamma Transmit FC2125E
Absolute Beta, Delta, Gamma Transmit FC2125E Absolute Beta, Delta, Gamma Receive
|
|
USB Rev 2.0 April 2000
|
FS (12 Mb/s)
HS:T1, T2, T3, T4, T5, T4 (480 Mb/s)
|
|
InfiniBand (draft)
|
2.5 Gb/s Optical 2.5 Gb/s Electrical
|
|
IEEE 1394b (draft)
|
S400 Optical
S400b T1,
S400b T2
S800 Optical
S800b
T1,
S800b T2
S1600 Optical
S1600b T1,
S1600b T2
|
|
Serial ATA (Rev 1.0 June 2002)
|
G1 Rx (5 Cycle), G1 Tx (5 Cycle)
|
|
Rapid IO LP_LVDS Rev 0.3 (draft) 5/2002
|
+Drv: 500 Mb/s, 750 Mb/s, 1 Gb/s, 1.5 Gb/s, 2.0 Gb/s
+Ext Drv:
500 Mb/s, 750 Mb/s, 1 Gb/s, 1.5 Gb/s, 2.0 Gb/s
+Rcv: 500 Mb/s, 750 Mb/s,
1 Gb/s, 1.5 Gb/s, 2.0 Gb/s
|
|
Rapid IO Serial Rev 1.1 December, 2001
|
RIO Serial: 1.25 Gb/s, 2.5 Gb/s
|
|
OIF Standards Draft 1.13 June 5,2002
|
SFI-5, SPI-5 TA/TC/RB/RD data/clock (2.4888 Gb/s)
SFI-5, SPI-5
TC Data (2.4888 Gb/s)
SFI-5, SPI-5 TA Clk (2.4888 Gb/s)
SFI-5,
SPI-5 TC Clk (2.4888 Gb/s)
SFI-5, SPI-5 Data (2.4888 Gb/s)
SFI-5,
SPI-5 RD Data (2.4888 Gb/s)
SFI-5, SPI-5 RB Clk (2.4888 Gb/s)
SFI-5,
SPI-5_5 RD Clk (2.4888 Gb/s)
VSR OC 192/STM64 1.24416 Gb/s
TFI-5
(2.4888 Gb/s)
|
|
PCI-Express Rev 1.0
|
Transmit/Receive (2.5 Gb/s)
|
Timebase System
|
|
CSA7404B
|
|
Timebase Range
|
50 ps to 10 s/div
|
|
Timebase Delay Time Range
|
5 ns to 250 s
|
|
Channel to Channel Deskew Range
|
±75 ns in 1 ps steps
|
|
Time Interval Accuracy, single-shot sample mode
|
(0.06/sample rate + 2.5 ppm x |reading|) RMS
|
|
Trigger Jitter
|
1.5 psRMS typical
|
|
Long Term Sample Rate and Delay Time Accuracy
|
±2.5 ppm over ≥100 ms interval; aging <1 ppm per year from date
of factory calibration
|
|
External Timebase Reference
|
Rear Panel Connection
|
|
External Reference Input Frequency Range
|
9.8 MHz to 10.2 MHz
|
|
External Reference Input Sensitivity
|
Vin≥200 mVp-p
|
|
External Reference Maximum input signal
|
7 Vp-p
|
|
Internal Reference Output Frequency
|
±2.5 ppm over ≥100 ms interval; aging <1 ppm per year from date
of factory calibration
|
|
Internal Reference Output Voltages
|
Vout (Hi) ≥2.5 V open circuit; ≥1.0 V into 50 Ω load to
gnd
Vout (Lo) ≤0.7 V into a load of ≤4 mA; ≤0.25 V into
50 Ω load to gnd
|
Acquisition System
|
Real-time Sample Rates
|
CSA7404B
|
|
1 channel (Max. rate)
|
20 GS/s
|
|
2 channels (Max. rate)
|
10 GS/s
|
|
3-4 channels (Max. rate)
|
5 GS/s
|
|
Equivalent time sample rate (Maximum)
|
1 TS/s
|
|
Maximum record length per channel with standard memory
|
4 M (1 ch), 2 M (2 ch), 1 M (4 ch)
|
|
With Memory Opt. 2M
|
8 M (1 ch), 4 M (2 ch), 2 M (4 ch)
|
|
With Memory Opt. 3M
|
16 M (1 ch), 8 M (2 ch), 4 M (4 ch)
|
|
With Memory Opt. 4M
|
32 M (1 ch), 16 M (2 ch), 8 M (4 ch)
|
|
With Memory Opt. 5M
|
64 M (1 ch), 32 M (2 ch), 16 M (4 ch)
|
Maximum Duration at Highest Real-time Resolution (1 ch)
|
|
CSA7404B
|
|
Time Resolution (single-shot)
|
50 ps (20 GS/s)
|
|
Maximum Duration with Standard Memory
|
200 μs
|
|
Maximum Duration with Opt. 2M
|
400 μs
|
|
Maximum Duration with Opt. 3M
|
800 μs
|
|
Maximum Duration with Opt. 4M
|
1.6 ms
|
|
Maximum Duration with Opt. 5M
|
3.2 ms
|
Acquisition Modes
|
|
CSA7404B
|
|
FastAcq Acquisition
|
Powered by DPX® acquisition technology, FastAcq optimizes the instrument
for analysis of dynamic signals and capture of infrequent events
|
|
Maximum FastAcq Waveform Capture Rate
|
>400,000 wfms/sec
|
|
Sample
|
Acquire sampled values
|
|
Waveform Database (WfmDB)
|
Accumulate waveform database providing three-dimensional array of
amplitude, time and counts
|
|
Peak Detect
|
Captures narrow glitches at all real time sampling rates
|
|
Minimum Peak Detect Pulse Width
|
400 ps
|
|
Average
|
From 2 to 10,000 waveforms included in average
|
|
Envelope
|
From 2 to 2x109 waveforms included in min-max envelope
|
|
Hi-Res
|
Real-time boxcar averaging reduces random noise and increases resolution
|
|
FastFrame Acquisition
|
Acquisition memory divided into segments; maximum trigger rate >265,000
waveforms per second. Time of arrival recorded with each event
|
Trigger System
|
|
CSA7404B
|
|
Sensitivity
|
|
Trigger Level Range
|
|
Internal DC Coupled, Main Trigger
|
0.5 div from DC to 50 MHz, ≤1.5 div at 3 GHz
|
|
External (Auxiliary Input)
|
150 mV from DC to 50 MHz increasing to 500 mV at 2.5 GHz
|
|
Main Trigger Modes
|
Auto, Normal and Single
|
|
Trigger Sequences
|
Main, Delayed by Time, Delayed by Events. All sequences can include
separate horizontal delay after the trigger event to position the acquisition
window in time
|
|
Internal
|
±12 divisions from center of screen
|
|
External (Auxiliary Input)
|
±5 V
|
|
Line
|
fixed at 0 V
|
|
Trigger Coupling
|
DC, AC (attenuate <60 Hz), HF Rej (attenuate >30 kHz), LF Rej (attenuates
<80 kHz), Noise Reject (reduce sensitivity)
|
|
Trigger Holdoff Modes
|
Random, Automatic or User-Specified Time
|
|
Trigger Holdoff Range
|
250 ns minimum to 12 seconds maximum
|
Trigger Modes
Edge - Positive and/or negative
slope on any channel or front panel auxiliary input. Coupling includes DC,
AC, noise reject, HF reject and LF reject.
Comm - Support for
AMI, HDB3, BnZS, CMI, MLT3 and NRZ encoded communications signals.
AMI encoding:
Standards include DS1, DS1A, DS1C, DS3, E1, E2, E3, STS-1 or a custom bit
rate. Select between positive or negative isolated one, zero pulse form or
eye patterns.
HDB3 encoding: Standards include E1, E2, E3, DS1A or
custom bit rate. Select between positive or negative isolated one pulse or
eye pattern.
BnZS encoding: Standards include DS1, DS1C, DS2, DS3,
STS-1 or custom bit rate. Select between positive or negative isolated one
pulse or eye pattern.
CMI encoding: Standards include STS-3, STM1E,
DS4NA, E4 or a custom bit rate. Select between positive or negative one pulse,
zero pulse or eye pattern.
MLT3 encoding: Standards include 100 Base-TX.
NRZ
encoding: Standards include OC1/STM0, OC3/STM1, OC12/STM4, OC48/STM16, GB
Ethernet, FC133, FC266, FC531, FC1063, FC2125, Infiniband 2.5, G1 ATA, FS
USB, HS USB, IEEE 1394b S400b, S800b, S1600b, OC-48 FEC, 1000 BASE CX, RapidIO,
SFI-5, SPI-5, VSR, PCI-Express, TFI-5; eye patterns only. CSA7154 limited
to standards ≤1.25 Gb/s.
Serial Pattern - 64-Bit serial
word recognizer, bits specified in binary (high, low, don't care) or hex format.
Trigger on NRZ-encoded data up to 1.25 Gbaud.
Glitch - Trigger
on or reject glitches of positive, negative, or either polarity. Minimum glitch
width is 1.0 ns with 200 ps resolution. Minimum glitch width is 225 ps with
rearm time of 250 ps.
Width - Trigger on width of positive
or negative pulse (down to 225 ps) either within or out of selectable time
limits: 340 ps to 1 s.
Runt - Trigger on a pulse that crosses
one threshold but fails to cross a second threshold before crossing the first
again. Optional time qualification.
Timeout - Trigger on an
event which remains high, low, or either, for a specified time period, selectable
from 340 ps to 1 s with 100 ps resolution.
Transition - Trigger
on pulse edge rates that are faster or slower than specified. Slope may be
positive, negative, or either.
Setup/Hold - Trigger on violations
of both setup time and hold time between clock and data present on any two
input channels.
Pattern - Trigger when pattern goes false or
stays true for specified period of time. Pattern (AND, OR, NAND, NOR) specified
for four input channels defined as HIGH, LOW or Don't Care.
State
- Any logical pattern of channels (1, 2, 3) clocked by edge on channel
4. Trigger on rising or falling clock edge.
Window - Trigger
on an event that enters or exits a window defined by two user-adjustable thresholds.
Event can be time or logic qualified.
Logic Qualified Trigger applicable
to Glitch, Width, Runt, Timeout, Transition, Setup/Hold, Window triggers —
trigger on the specified event only if the logic state defined with the remaining
unused channels occurs.
Trigger Delay by Time - Trigger
Delay by Time 5 ns to 250 seconds.
Trigger Delay by Events - Trigger
Delay by Events 1 to 10,000,000 Events.
Waveform Measurements
Amplitude
- Amplitude, High, Low, Maximum, Minimum, Peak to Peak, Mean, Cycle Mean,
RMS, Cycle RMS, Positive Overshoot, Negative Overshoot.
Time - Rise
time, Fall time, Positive Width, Negative Width, Positive Duty Cycle, Negative
Duty Cycle, Period, Frequency, Delay.
Combination - Area, Cycle
Area, Phase, Burst Width.
Histogram-related - Waveform count,
Hits in box, Peak hits, Median, Maximum, Minimum, Peak to Peak, Mean (μ),
Standard Deviation (σ), μ+1σ, μ+2σ, μ+3σ.
Eye Pattern-related - Extinction
Ratio (absolute, % and dB), Eye Height, Eye Top, Eye Base, Eye Width, Crossing
%, Jitter (peak-peak, RMS and 6sigma), Noise (peak-peak and RMS), S/N ratio,
Cycle Distortion, Q-factor.
Waveform Processing/Math
Algebraic
Expressions - Define extensive algebraic expressions including waveforms,
scalars and results of parametric measurements e.g. (Integral (Ch. 1-Meas(Ch. 1))×1.414).
Arithmetic
- Add, subtract, multiply, divide waveforms and scalars.
Relational
- Boolean result of comparison >, <, ≥, ≤, ==, !=.
Calculus
- Integrate, differentiate.
Frequency Domain Functions - Spectral
magnitude and phase, real and imaginary spectra.
Vertical Units
- Magnitude: Linear, dB, dBm.
Phase: degrees, radians.
Window
Functions - Rectangular, Hamming, Hanning, Kaiser-Bessel, Blackman-Harris,
Gaussian, Flattop2, Tek Exponential.
Waveform Definitions - Waveform
definition as arbitrary math expressions.
Display Characteristics
Display
Type - Liquid crystal active-matrix color display; integral touch screen.
Display
Size - 211.2 mm (W) x 158.4 mm (H), 264 mm (10.4 in.) diagonal.
Display
Resolution - 1024 horizontal x 768 vertical pixels.
Waveform
Styles - Vectors, Dots, Variable Persistence, Infinite Persistence.
Computer
System and Peripherals
CPU - Intel Pentium IV processor, 2.8 GHz*2
PC
System Memory - 1 GB*2.
Hard Disk Drive - 40 GB
removable hard disk drive: rear-panel, or (B model only) front-panel (option
FHD).
Floppy Disk Drive - 1.44 MB 3.5 in floppy disk drive:
front-panel, or rear-panel (option FHD).
CD-RW Drive - Rear-panel
CD-RW drive.
Mouse - Thumb wheel model included, USB interface.
Keyboard
- Mini-keyboard included (fits in pouch); PS-2 interface. Order 119-6633-00
for full-size keyboard; USB interface and hub.
*2 Available
September 2004.
Input/Output Ports
Probe Compensation
Output - Front panel BNC connector, requires Probe Cal-Deskew Fixture
(included) for probe attachment.
1 V ±20% into >10 kΩ load
500 mV
±20% into a 50 Ω load.
Recovered Clock Out - Front-panel
SMA connector provides output of clock signal recovered from specified channel.
Output compatible with ECL terminated with 50 Ω to GND. Peak-to-peak output
swing at 650 MHz is at least 200 mV into 50 Ω. Higher frequencies will be
further attenuated by approximately 6 dB per octave above 625 MHz.
Recovered
Data Out - Front-panel SMA connector provides regenerated data output
from clock recovery system. Serial data output baud rate ≤1250 MBaud. Output
swing at this baud rate will be at least 200 mV into 50 Ω.
Optical
In - Optoelectronic converter input, 700 nm to 1650 nm, Rifocs connector.
O/E
Output - Front-panel BMA connector providing electrical output of optoelectronic
converter. SMA adapter included.
Analog Signal Output Amplitude
- Rear-panel BNC connector, provides a buffered version of the signal
that is attached to the Channel 3 input when Ch. 3 is selected as trigger
source. Frequency response: 1.8 GHz into a 50 Ω load. Amplitude: 20 mV/div
±20% into a 1 MΩ load, 10 mV/div ±20% into a 50 Ω load.
Auxiliary
Output - Rear-panel BNC connector, provides a TTL-compatible, polarity
switchable pulse when the oscilloscope triggers or optionally, upon mask test
failure or test completion.
External Timebase Reference In - Rear-panel
BNC connector, timebase system can phase-lock to external 10 MHz reference.
Timebase
Reference Out - Rear-panel BNC connector, provides TTL-compatible output
of internal 10 MHz reference oscillator.
Parallel Port - IEEE
1284, DB-25 connector.
Audio Ports - Miniature phone jacks
for stereo microphone input and stereo line output.
USB Port - Allows
connection or disconnection of USB keyboard, mouse or other peripherals while
oscilloscope power is on. Two USB ports.
Keyboard Port - PS-2
compatible.
Mouse Port - PS-2 compatible.
LAN Port
- RJ-45 connector, supports 10 Base-T and 100 Base-T.
Serial
Port - DB-9 COM1 port.
Windows Video Port - 15 pin D-Sub
connector on the rear panel; connect a second monitor to use dual-monitor
display mode. Video is DDC2B compliant
GPIB Port - IEEE 488.2
standard.
Scope Video Port - 15 pin D-Sub connector on the
rear panel, video is IBM XGA compatible for B models. Connect to show the
oscilloscope display, including live waveforms on an external monitor or projector.
The primary Windows desktop can also be displayed on an external monitor using
this port.
Power Source
Power - 100 to 240 VRMS,
±10%, 50/60 Hz CAT II.
115 VRMS ±10%, 400 Hz CAT II.
<300 Watts
(450 VA).
Physical Characteristics
|
BENCHTOP CONFIGURATION
|
|
Dimensions
|
mm
|
in.
|
|
Weight
|
kg
|
lb.
|
|
RACKMOUNT CONFIGURATION
|
|
Dimensions
|
mm
|
in.
|
|
Weight
|
kg
|
lb.
|
|
MECHANICAL
|
|
Required Clearance
|
mm
|
in.
|
|
Height
|
277
|
10.9
|
|
Width
|
455
|
17.9
|
|
Depth
|
425
|
16.75
|
|
Net
|
19
|
41.5
|
|
Shipping
|
37
|
85
|
|
Height
|
277
|
10.9
|
|
Width
|
502
|
19.75
|
|
Depth
|
486
|
19.125
|
|
Net
|
20
|
43.5
|
|
Shipping
|
5.6
|
12.32
|
|
Top
|
0 or >76
|
0 or >3
|
|
Bottom
|
0
|
0
|
|
Left side
|
76
|
3
|
|
Right side
|
76
|
3
|
|
Front
|
0
|
0
|
|
Rear
|
0
|
0
|
Environmental
Temperature -
Operating:
0 °C
or 5 °C (B models) to +50 °C, excluding floppy disk and CD-RW drives.
+10 °C
to +45 °C, including floppy disk and CD-RW drives.
Nonoperating: -22 °C
to +60 °C.
Humidity -
Operating: 20% to 90% relative
humidity with a maximum wet bulb temperature of +29 °C at or below +50 °C,
noncondensing. Upper limit derated to 25% relative humidity at +50 °C.
Nonoperating:
With no diskette in floppy disk drive, 20% to 90% relative humidity with a
maximum wet bulb temperature of +29 °C at or below +60 °C, noncondensing.
Upper limit derated to 20% relative humidity at +60 °C.
Altitude
-
Operating: 10,000 ft. (3,048 m).
Nonoperating: 40,000 ft.
(12,190 m).
Random Vibration -
Operating: 0.00015 g2/Hz
from 5 to 350 Hz,
-3 dB/octave from 350 to 500 Hz,
0.000105 g2/Hz
at 500 Hz.
Overall level of 0.27 gRMS.
Nonoperating:
0.0175 g2/Hz from 5 to 100 Hz,
-3 dB/octave from 100 to
200 Hz,
0.0875 g2/Hz from 200 to 350 Hz,
-3 dB/octave
from 350 to 500 Hz,
0.006132 g2/Hz at 500 Hz.
Overall
level of 2.28 gRMS.
Electromagnetic Compatibility
- EN 61326 (EU EMC Directive 89/336 EEC).
AS/NZS 2064 (Australian EMC
Framework).
Safety - UL 3111-1, CSA-22.2 No. 1010.1, EN61010-2.
Ordering
Information
CSA7404B
4 GHz Communications Signal Analyzer
Includes: Accessory
pouch, front keyboard cover, mouse, probe calibration and deskew fixture (067-0405-xx),
O/E Electrical Output to Ch. 1 Input Adapter (013-0327-xx), Fiber cleaning
kit (020-2494-xx), GPIB Programmer's Reference, Optional Applications Software
CD-ROM, Oscilloscope Analysis and Connectivity Made Easy Kit, Performance
verification procedure PDF file, NIST, MIL-STD-45662A, ISO9000 Calibration
Certificate and Power Cord.
CSA7404B also includes: (4) TekConnect®
to SMA adapters (TCA-SMA), Quick Reference (020-2519-xx), User Manual (071-1226-xx),
Option SM and ST User Manual (071-1228-xx), TDS/CSA7000B Series Product Software
CD-ROM, and TDS/CSA7000B Series operating system restoration CD-ROM
Please
specify power plug and disk drive option when ordering.
Instrument
Options
Power Plug Options
Opt. A0 - North
America power.
Opt. A1 - Universal EURO power.
Opt.
A2 - United Kingdom power.
Opt. A3 - Australia power.
Opt.
A5 - Switzerland power.
Opt. A6 - Japan power.
Opt.
A10 - China power.
Opt. A99 - No power cord or AC adapter.
Mounting
Options
Opt. 1K - K4000 Scope cart.
Opt. 1R
- Rackmount kit.
Disk Drive Options
Opt FHD
- Front–panel 40 GB removable hard disk drive, replaces floppy disk drive
that goes on the rear-panel
Service Options
Opt.
C3 - Calibration Service 3 Years
Opt. C5 - Calibration
Service 5 Years
Opt. D1 - Calibration Data Report
Opt.
D3 - Calibration Data Report 3 Years (with Option C3)
Opt.
D5 - Calibration Data Report 5 Years (with Option C5)
Opt.
R3 - Repair Service 3 Years
Opt. R5 - Repair Service 5
Years
Recommended Accessories
Probes and Converters
P7260
- 6 GHz Low Capacitance Active Voltage Probe (TekConnect®).
P7350
- 5 GHz Differential Probe (TekConnect®).
P7350SMA - 5 GHz
SMA Input differential Probe
P6150 - 9 GHz Low Capacitance
Passive Voltage Probe (requires TCA-SMA adapter).
P6158 - 3 GHz
Low Capacitance Passive Voltage Probe (requires TCA-BNC adapter).
CT6
- 2 GHz AC Current Probe (requires TCA-BNC adapter).
CT1 - 1 GHz
AC Current Probe (requires TCA-BNC adapter).
P6701B - Optical-to-Electrical
Converter; 500 nm to 950 nm (requires TCA-BNC adapter).
P6703B
- Optical-to-Electrical Converter; 1100 nm to 1650 nm (requires TCA-BNC
adapter).
TCP202 - DC to 50 MHz Current Probe (requires TCA-BNC
adapter).
P6245 - 1.5 GHz Active Probe.
P6248 - 1.7 GHz
Differential Probe.
P6250 - DC to 500 MHz, 42 V, Differential
Probe (requires TCA-BNC adapter).
P6251 - DC to 1 GHz, 42 V,
Differential Probe (requires TCA-BNC adapter).
P7240 - 4 GHz
Active Probe.
P7330 - 3.5 GHz Differential Probe.
Adapters
TCA75
- 4 GHz precision TekConnect® 75 Ω to 50 Ω adapter with 75 Ω BNC input
connector.
TCA-SMA - TekConnect-to-SMA Adapter.
TCA-BNC
- TekConnect-to-BNC Adapter.
TCA-N - TekConnect-to-N Adapter.
TCA-1Meg
- 1 Meg amplifier, high impedance buffer 1 MΩ/10 pF, TekProbe BNC-to-TekConnect®;
includes P6139A.
AFTDS - Telecom differential electrical interface
adapter (for line rates <8 Mb/s; requires TCA-BNC adapter).
AMT75
- 1 GHz precision 75 Ω adapter (for line rates >8 Mb/s; requires TCA-BNC
adapter).
Optical Connector Adapters
FC/PC - Order
119-5115-00.
SC/PC - Order 119-5116-00.
ST/PC - Order
119-4513-00.
DIN/PC 47256 - Order 119-4546-00.
Diamond
2.5 - Order 119-4556-00.
Diamond 3.5 - Order 119-4558-00.
SMA
2.5 - Order 119-4517-00.
SMA - Order 119-4557-00.
Cables
GPIB
Cable (1M) - Order 012-0991-01.
GPIB Cable (2M) - Order
012-0991-00.
Centronics Cable - Order 012-1214-00.
Test
Fixtures
TDSUSBF - USB test fixture to be used in conjunction
with Opt. USB
Software
WSTRO - Wavestar™ waveform
capture and documentation software.
Miscellaneous
Keyboard
- Full size, USB interface; Order 119-6633-00.
Service Manual
- Order 071-1227-xx.
Transit Case - Order 016-1522-00.
Options
(available on models indicated by "x")
|
|
|
CSA7404B
|
|
Acquisition Memory Options
|
|
Software Options
|
|
2M
|
8 Msamples max, 2 Msamples/ch
|
x
|
|
3M
|
16 Msamples max, 4 Msamples/ch
|
x
|
|
4M
|
32 Msamples max, 8 Msamples/ch
|
x
|
|
5M
|
64 Msamples max, 16 Msamples/ch
|
x
|
|
DVI
|
TDSDVI DVI compliance test solution
|
x
|
|
DVD
|
TDSDVD Optical storage analysis
|
x
|
|
ET3
|
TDSET3 Ethernet compliance test software
|
x
|
|
JA3
|
TDSJIT3 Advanced jitter analysis software
|
x
|
|
JE3
|
TDSJIT3 Essentials
|
x
|
|
J2
|
TDSDDM2 Disk drive analysis software
|
x
|
|
CP2
|
TDSCPM2 ANSI/ITU Telecom pulse compliance testing software
|
x
|
|
USB*1
|
TDSUSBS USB2.0 Compliance test S/W only
|
x
|
|
PW3
|
TDSPWR3 Power measurement and analysis software
|
x
|
|
RTE
|
Serial Data Compliance and Analysis Software
|
x
|
|
PCE*2
|
PCI Express™ Compliance Module for option RTE
|
|
|
IBA*2
|
InfiniBand® Compliance Module for option RTE
|
|
*1 Requires Option TDSUSBF (USB Test Fixture).
*2 Requires
Option RTE.
To view instrument upgrades, please go to www.tektronix.com/csa7000b_upgrades.
