Features & Benefits
Key Performance Specifications
- 1 GHz, 500 MHz, 350 MHz Bandwidth Models
- 4 Analog
Channel Models
- 16 Digital Channels (MSO Series)
- Up to 5 GS/s Sample Rate on All Channels
- 20 Megapoint Record
Length on All Channels
- >50,000 wfm/s Maximum Waveform Capture
Rate
- Standard Passive Voltage Probes with Less than 4 pF
Capacitive Loading and 500 MHz or 1 GHz Analog Bandwidth
- Suite of Advanced Triggers
Ease of Use Features
- Wave Inspector® Controls provide Easy Navigation
and Automated Search of Waveform Data
- 41 Automated Measurements,
Waveform Histograms, and FFT Analysis for Simplified Waveform Analysis
- TekVPI® Probe Interface supports Active, Differential,
and Current Probes for Automatic Scaling and Units
- 10.4 in.
(264 mm) Bright XGA Color Display
- Small Footprint and Lightweight
– Only 5.8 in. (147 mm) deep and 11 lb. (5 kg)
Connectivity
- Two USB 2.0 Host Ports on the Front Panel and Two on the
Rear Panel for Quick and Easy Data Storage, Printing, and Connecting
a USB Keyboard
- USB 2.0 Device Port on Rear Panel for Easy
Connection to a PC or Direct Printing to a PictBridge®-compatible
Printer
- Integrated 10/100/1000BASE-T Ethernet Port for Network
Connection and Video Out Port to Export the Oscilloscope Display to
a Monitor or Projector
Optional Serial Triggering and
Analysis
- Automated Serial Triggering, Decode, and Search
Options for I2C, SPI, USB, Ethernet, CAN, LIN, FlexRay,
RS-232/422/485/UART, MIL-STD-1553, and I2S/LJ/RJ/TDM
Mixed Signal Design and Analysis (MSO Series)
- Automated Triggering, Decode, and Search on Parallel Buses
- Per-channel Threshold Settings
- Multichannel Setup and
Hold Triggering
- MagniVu™ High-speed Acquisition Provides
60.6 ps Fine Timing Resolution on Digital Channels
Optional Application Support
- Power Analysis
- Limit and Mask Testing
- HDTV and Custom Video Analysis
Feature-rich
Tools for Debugging Mixed Signal Designs
With the MSO/DPO4000B
Mixed Signal Oscilloscope Series, you can analyze up to 20 analog
and digital signals with a single instrument to quickly find and diagnose
problems in complex designs. Bandwidths up to 1 GHz and a minimum
of 5X oversampling on all channels ensure you have the performance
you need to see fast-changing signal details. To capture long windows
of signal activity while maintaining fine timing resolution, the MSO/DPO4000B
Series offers a deep record length of 20M points standard on all channels.
With Wave Inspector® controls for rapid waveform navigation,
automated serial and parallel bus analysis, limit and mask testing,
and automated power analysis – the MSO/DPO4000B Oscilloscope Series
from Tektronix provides the feature-rich tools you need to simplify
and speed debug of your complex design.
Comprehensive Features
Speed Every Stage of Debug
The MSO/DPO4000B Series offers
a robust set of features to speed every stage of debugging your design
– from quickly discovering an anomaly and capturing it, to searching
your waveform record for the event and analyzing its characteristics
and your device's behavior.
Discover
Discover – Fast waveform capture rate - over 50,000 wfm/s
- maximizes the probability of capturing elusive glitches and other
infrequent events.
To debug a design problem,
first you must know it exists. Every design engineer spends time looking
for problems in their design, a time-consuming and frustrating task
without the right debug tools.
The MSO/DPO4000B Series offers
the industry's most complete visualization of signals, providing fast
insight into the real operation of your device. A fast waveform capture
rate - greater than 50,000 waveforms per second - enables you to see
glitches and other infrequent transients within seconds, revealing
the true nature of device faults. A digital phosphor display with
intensity grading shows the history of a signal's activity by intensifying
areas of the signal that occur more frequently, providing a visual
display of just how often anomalies occur.
Capture
Capture – Triggering on a specific transmit data packet
going across an RS-232 bus. A complete set of triggers, including
triggers for specific serial packet content, ensures you quickly capture
your event of interest.
Discovering a device
fault is only the first step. Next, you must capture the event of
interest to identify root cause.
Accurately capturing any signal
of interest begins with proper probing. The MSO/DPO4000B Series includes
four low-capacitance probes for accurate signal capture. These industry-first
high-impedance passive voltage probes have less than 4 pF of capacitive
loading to minimize the affect of the probe on your circuit's operation,
offering the performance of an active probe with the flexibility of
a passive probe.
The MSO/DPO4000B Series provides a complete
set of triggers – including runt, timeout, logic, pulse width/glitch,
setup/hold violation, serial packet, and parallel data – to help quickly
find your event. With up to a 20M point record length, you can capture
many events of interest, even thousands of serial packets, in a single
acquisition for further analysis while maintaining high resolution
to zoom in on fine signal details.
From triggering on specific
packet content to automatic decode in multiple data formats, the MSO/DPO4000B
Series provides integrated support for the industry's broadest range
of serial buses – I2C, SPI, USB, Ethernet, CAN, LIN, FlexRay,
RS-232/422/485/UART, MIL-STD-1553, and I2S/LJ/RJ/TDM. The
ability to decode up to four serial and/or parallel buses simultaneously
means you gain insight into system-level problems quickly.
To further help troubleshoot system-level interactions in complex
embedded systems, the MSO4000B Series offers 16 digital channels in
addition to its analog channels. Since the digital channels are fully
integrated into the oscilloscope, you can trigger across all input
channels, automatically time correlating all analog, digital, and
serial signals. The MagniVu™ high-speed acquisition enables you to
acquire fine signal detail (up to 60.6 ps resolution) around the trigger
point for precision measurements. MagniVu is essential for making
accurate timing measurements for setup and hold, clock delay, signal
skew, and glitch characterization.
Search
Search – I2C decode showing results from a Wave
Inspector search for Address value 50. Wave Inspector controls provide
unprecedented efficiency in viewing and navigating waveform data.
Finding your event of interest in a long waveform
record can be time consuming without the right search tools. With
today's record lengths pushing beyond a million data points, locating
your event can mean scrolling through thousands of screens of signal
activity.
The MSO/DPO4000B Series offers the industry's most
comprehensive search and waveform navigation with its innovative Wave
Inspector® controls. These controls speed panning and zooming
through your record. With a unique force-feedback system, you can
move from one end of your record to the other in just seconds. User
marks allow you to mark any location that you may want to reference
later for further investigation. Or, automatically search your record
for criteria you define. Wave Inspector will instantly search your
entire record, including analog, digital, and serial bus data. Along
the way it will automatically mark every occurrence of your defined
event so you can quickly move between events.
Analyze
Analyze – Waveform histogram of a falling edge showing
the distribution of edge position (jitter) over time. Included are
numeric measurements made on the waveform histogram data. A comprehensive
set of integrated analysis tools speeds verification of your design's
performance.
Verifying that your prototype's
performance matches simulations and meets the project's design goals
requires analyzing its behavior. Tasks can range from simple checks
of rise times and pulse widths to sophisticated power loss analysis
and investigation of noise sources.
The MSO/DPO4000B Series
offers a comprehensive set of integrated analysis tools including
waveform- and screen-based cursors, 41 automated measurements, advanced
waveform math including arbitrary equation editing, waveform histograms,
FFT analysis, and trend plots for visually determining how a measurement
is changing over time. Specialized application support for serial
bus analysis, power supply design, limit and mask testing, and video
design and development is also available.
For extended analysis,
National Instrument's LabVIEW SignalExpress™ Tektronix Edition provides
over 200 built-in functions including time and frequency domain analysis,
data logging, and customizable reports.
Wave Inspector® Navigation and Search
Wave Inspector controls
provide unprecedented efficiency in viewing, navigating, and analyzing
waveform data. Zip through your 20M point record by turning the outer
pan control (1). Get from the beginning to end in seconds. See something
of interest and want to see more details? Just turn the inner zoom
control (2).
A 20M point record length represents
thousands of screens of information. The MSO/DPO4000B Series enables
you to find your event in seconds with Wave Inspector, the industry's
best tool for navigation and search.
Wave Inspector offers
the following innovative controls:
Zoom/Pan
A dedicated,
two-tier front-panel control provides intuitive control of both zooming
and panning. The inner control adjusts the zoom factor (or zoom scale);
turning it clockwise activates zoom and goes to progressively higher
zoom factors, while turning it counterclockwise results in lower zoom
factors and eventually turning zoom off. No longer do you need to
navigate through multiple menus to adjust your zoom view. The outer
control pans the zoom box across the waveform to quickly get to the
portion of waveform you are interested in. The outer control also
utilizes force feedback to determine how fast to pan on the waveform.
The farther you turn the outer control, the faster the zoom box moves.
Pan direction is changed by simply turning the control the other way.
Play/Pause
A dedicated Play/Pause front-panel
button scrolls the waveform across the display automatically while
you look for anomalies or an event of interest. Playback speed and
direction are controlled using the intuitive pan control. Once again,
turning the control further makes the waveform scroll faster and changing
direction is as simple as turning the control the other way.
Search step 1: You define what you would like to find.
Search step 2: Wave Inspector automatically searches
through the record and marks each event with a hollow white triangle.
You can then use the Previous and Next buttons to jump
from one event to the next.
User Marks
Press the Set Mark front-panel button to place one or
more marks on the waveform. Navigating between marks is as simple
as pressing the Previous (←) and Next (→) buttons on
the front panel.
Search Marks
The Search button
allows you to automatically search through your long acquisition looking
for user-defined events. All occurrences of the event are highlighted
with search marks and are easily navigated to, using the front-panel Previous (←) and Next (→) buttons. Search types include
edge, pulse width/glitch, timeout, runt, logic, setup and hold, rise/fall
time, parallel bus, and I2C, SPI, USB, Ethernet, CAN, LIN,
FlexRay, RS-232/422/485/UART, MIL-STD-1553, and I2S/LJ/RJ/TDM
packet content.
Digital Phosphor Technology
Digital phosphor technology enables greater than 50,000 wfm/s
waveform capture rate and real-time intensity grading on the MSO/DPO4000B
Series.
The MSO/DPO4000B Series' digital phosphor
technology provides you with fast insight into the real operation
of your device. Its fast waveform capture rate - greater than 50,000 wfm/s
- gives you a high probability of quickly seeing the infrequent problems
common in digital systems: runt pulses, glitches, timing issues, and
more.
Waveforms are superimposed with one another and waveform
points that occur more frequently are intensified. This quickly highlights
the events that over time occur more often or, in the case of infrequent
anomalies, occur less often.
With the MSO/DPO4000B Series,
you can choose infinite persistence or variable persistence (including
zero persistence), determining how long the previous waveform acquisitions
stay on-screen. This allows you to determine how often an anomaly
is occurring.
Accurate High-speed Probing
The TPP
Series probes, included standard with every MSO/DPO4000B Series oscilloscope,
provide up to 1 GHz of analog bandwidth, and less than 4 pF of capacitive
loading. The extremely low capacitive loading minimizes adverse affects
on your circuits and is more forgiving of longer ground leads. And,
since the probe bandwidth matches your oscilloscope bandwidth, you
can see the high-frequency components in your signal which is critical
for high-speed applications. The TPP Series passive voltage probes
offer all the benefits of general-purpose probes like high dynamic
range, flexible connection options, and robust mechanical design,
while providing the performance of active probes.
Mixed Signal
Design and Analysis(MSO Series)
The MSO Series provides
16 integrated digital channels enabling you to view and analyze time-correlated
analog and digital signals.
The MSO4000B Series
Mixed Signal Oscilloscopes provide 16 digital channels. These channels
are tightly integrated into the oscilloscope's user interface, simplifying
operation and making it possible to solve mixed-signal issues easily.
Color-coded Digital Waveform Display
With the color-coded
digital waveform display, groups are created by simply placing digital
channels together on the screen, allowing the digital channels to
be moved as a group. You can set threshold values for each channel,
enabling support for up to 16 different logic families.
The MSO4000B Series has redefined the way you view digital
waveforms. One common problem shared by both logic analyzers and mixed
signal oscilloscopes is determining if data is a one or a zero when
zoomed in far enough that the digital trace stays flat all the way
across the display. The MSO4000B Series has color-coded digital traces,
displaying ones in green and zeros in blue.
White edges
indicate additional information is available by zooming in. As shown
here, zooming in on the white edge reveals a hidden glitch.
The multiple transition detection hardware of the
MSO4000B Series will show you a white edge on the display when the
system detects multiple transitions. White edges indicate that more
information is available by zooming in or acquiring at faster sampling
rates. In most cases zooming in will reveal the pulse that was not
viewable with the previous settings. If the white edge is still present
after zooming in as far as possible, this indicates that increasing
the sample rate on the next acquisition will reveal higher frequency
information than the previous settings could acquire.
The MSO4000B
Series simplifies channel setup by allowing you to group digital waveforms
and enter waveform labels by using a USB keyboard. By simply placing
digital waveforms next to each other, they form a group. Once a group
is formed, you can position all the channels contained in that group
collectively. This greatly reduces the normal setup time associated
with positioning channels individually.
MagniVu™ High-speed
Acquisition
The MagniVu high-resolution
record provides 60.6 ps timing resolution, enabling you to make critical
timing measurements on your digital waveforms.
The main digital acquisition mode on the MSO4000B Series will capture
up to 20M points at 500 MS/s (2 ns resolution). In addition to the
main record, the MSO4000B Series provides an ultra high-resolution
record called MagniVu which acquires 10,000 points at up to 16.5 GS/s
(60.6 ps resolution). Both main and MagniVu waveforms are acquired
on every trigger and can be switched between in the display at any
time, running or stopped. MagniVu provides significantly finer timing
resolution than comparable MSOs on the market, instilling confidence
when making critical timing measurements on digital waveforms.
P6616 MSO Probe
The P6616 MSO probe offers
two eight-channel pods to simplify connecting to your device.
This unique probe design offers two eight-channel
pods. Each channel ends with a probe tip featuring a recessed ground
for simplified connection to the device under test. The coax on the
first channel of each pod is colored blue making it easy to identify.
The common ground uses an automotive-style connector making it easy
to create custom grounds for connecting to the device under test.
When connecting to square pins, the P6616 has an adapter that attaches
to the probe head extending the probe ground flush with the probe
tip so you can attach to a header. The P6616 offers outstanding electrical
characteristics, having only 3 pF of capacitive loading, a 100 kΩ
input resistance, and capable of acquiring toggle rates >500 MHz and
pulses as short as 1 ns in duration.
Serial Triggering and
Analysis (Optional)
Triggering on a specific
OUT Token packet on a USB full-speed serial bus. The yellow waveform
is the D+ and the blue waveform is the D–. A bus waveform provides
decoded packet content including Start, Sync, PID, Address, End Point,
CRC, Data values, and Stop.
On a serial bus,
a single signal often includes address, control, data, and clock information.
This can make isolating events of interest difficult. The MSO/DPO4000B
Series offers a robust set of tools for debugging serial buses with
automatic trigger, decode, and search for I2C, SPI, USB,
Ethernet, CAN, LIN, FlexRay, RS-232/422/485/UART, MIL-STD-1553, and
I2S/LJ/RJ/TDM.
Serial Triggering
Trigger
on packet content such as start of packet, specific addresses, specific
data content, unique identifiers, etc. on popular serial interfaces
such as I2C, SPI, USB, Ethernet, CAN, LIN, FlexRay, RS-232/422/485/UART,
MIL-STD-1553, and I2S/LJ/RJ/TDM.
Bus Display
Provides a higher-level, combined view of the individual signals
(clock, data, chip enable, etc.) that make up your bus, making it
easy to identify where packets begin and end and identifying subpacket
components such as address, data, identifier, CRC, etc.
Bus
Decoding
Tired of having to visually inspect the waveform
to count clocks, determine if each bit is a 1 or a 0, combine bits
into bytes, and determine the hex value? Let the oscilloscope do it
for you! Once you've set up a bus, the MSO/DPO4000B Series will decode
each packet on the bus, and display the value in hex, binary, decimal
(USB, Ethernet, MIL-STD-1553, LIN, and FlexRay only), signed decimal
(I2S/LJ/RJ/TDM only), or ASCII (USB, Ethernet, and RS-232/422/485/UART
only) in the bus waveform.
Event Table
Event table showing decoded Identifier, DLC, DATA, and CRC
for every CAN packet in a long acquisition.
In addition to seeing decoded packet data on the bus waveform itself,
you can view captured packets in a tabular view much like you would
see in a software listing. Packets are time stamped and listed consecutively
with columns for each component (Address, Data, etc.).
Search
Serial triggering is very useful for isolating the event of interest,
but once you've captured it and need to analyze the surrounding data,
what do you do? In the past, users had to manually scroll through
the waveform counting and converting bits and looking for what caused
the event. With the MSO/DPO4000B Series, you can have the oscilloscope
automatically search through the acquired data for user-defined criteria
including serial packet content. Each occurrence is highlighted by
a search mark. Rapid navigation between marks is as simple as pressing
the Previous (←) and Next (→) buttons on the front panel.
Power Analysis (Optional)
Safe operating area measurement.
Automated power measurements enable quick and accurate analysis of
common power parameters.
Ever increasing consumer
demand for longer battery-life devices and for green solutions that
consume less power require power-supply designers to characterize
and minimize switching losses to improve efficiency. In addition,
the supply's power levels, output purity, and harmonic feedback into
the power line must be characterized to comply with national and regional
power quality standards. Historically, making these and many other
power measurements on an oscilloscope has been a long, manual, and
tedious process. The MSO/DPO4000B Series optional power analysis tools
greatly simplify these tasks, enabling quick and accurate analysis
of power quality, switching loss, harmonics, safe operating area (SOA),
modulation, ripple, and slew rate (di/dt, dv/dt). Completely integrated
into the oscilloscope, the power analysis tools provide automated,
repeatable power measurements with a touch of a button; no external
PC or complex software setup is required.
Limit/Mask Testing
(Optional)
A common task during the development process is
characterizing the behavior of certain signals in a system. One method,
called limit testing, is to compare a tested signal to a known good
or "golden" version of the same signal with user-defined vertical
and horizontal tolerances. Another common method, called mask testing,
is to compare a tested signal to a mask, looking for where a signal
under test violates the mask. The MSO/DPO4000B Series offers both
limit and mask testing capability useful for long-term signal monitoring,
characterizing signals during design, or testing on a production line.
A robust set of telecommunications and computer standards are provided
to test for compliance to a standard. Additionally, custom masks can
be created and used for characterizing signals. Tailor a test to your
specific requirements by defining test duration in number of waveforms
or time, a violation threshold that must be met before considering
a test a failure, counting hits along with statistical information,
and actions upon violations, test failure, and test complete. Whether
specifying a mask from a known good signal or from a custom or standard
mask, conducting pass/fail tests in search of waveform anomalies such
as glitches has never been easier.
Video Design and Development
Limit Test showing a mask created from a golden waveform
and compared against a live signal. Results showing statistical information
about the test are displayed.
Many video engineers
have remained loyal to analog oscilloscopes, believing the intensity
gradations on an analog display are the only way to see certain video
waveform details. The MSO/DPO4000B Series fast waveform capture rate,
coupled with its intensity-graded view of the signal, provides the
same information-rich display as an analog oscilloscope, but with
much more detail and all the benefits of digital oscilloscopes.
Standard features such as IRE and mV graticules, holdoff by fields,
video polarity, and an Autoset smart enough to detect video signals,
make the MSO/DPO4000B Series the easiest to use oscilloscope on the
market for video applications. And with up to a 1 GHz bandwidth and
four analog inputs, the MSO/DPO4000B Series provides ample performance
for analog and digital video use.
The MSO/DPO4000B Series video
functionality is further extended with the optional DPO4VID video
application module. DPO4VID provides the industry's most complete
suite of HDTV and custom (nonstandard) video triggers.
Designed
to Make Your Work Easier
The MSO/DPO4000B Series
is designed to make your work easier. The large, high-resolution display
shows intricate signal details. Dedicated front-panel controls simplify
operation. Two USB host ports on the front panel allow you to easily
transfer screenshots, instrument settings, and waveform data to a
USB thumb drive.
Large, High-resolution Display
The MSO/DPO4000B Series features a 10.4 in. (264 mm) bright,
LED backlit XGA color display for seeing intricate signal details.
Dedicated Front-panel Controls
Per-channel vertical
controls provide simple and intuitive operation. No longer do you
need to share one set of vertical controls across all four channels.
Connectivity
Two USB host ports on the front panel enable
easy transfer of screenshots, instrument settings, and waveform data
to a USB thumb drive. The rear panel contains two additional USB host
ports and a USB device port for controlling the oscilloscope remotely
from a PC or for connecting a USB keyboard. The USB device port can
also be used to print directly to a PictBridge®-compatible
printer. An integrated 10/100/1000BASE-T Ethernet port enables easy
connection to networks and a Video Out port allows the oscilloscope
display to be exported to an external monitor or projector. The instrument
can mount external network drives for easy storage of screen images,
setup files, or data files. Setup or data files can then be directly
recalled and loaded into the oscilloscope from the network drive location.
The MSO/DPO4000B Series is LXI Class-C compliant.
Compact
Form Factor
The MSO/DPO4000B Series'
compact form factor frees up valuable space on your bench or desktop.
A compact, portable form factor allows the MSO/DPO4000B
Series to be easily moved between labs and, with a depth of just 5.8 in.
(147 mm), it saves you valuable space on your test bench.
TekVPI® Probe Interface
TekVPI probe
interface simplifies connecting your probes to the oscilloscope.
The TekVPI probe interface sets the standard for
ease of use in probing. In addition to the secure, reliable connection
that the interface provides, TekVPI probes feature status indicators
and controls, as well as a probe menu button right on the compensation
box itself. This button brings up a probe menu on the oscilloscope
display with all relevant settings and controls for the probe. The
TekVPI interface enables direct attachment of current probes without
requiring a separate power supply. TekVPI probes can be controlled
remotely through USB, GPIB, or LAN, enabling more versatile solutions
in ATE environments.
Extended Analysis
OpenChoice® Desktop software enables seamless
connection between the oscilloscope and your PC.
Acquiring data and measurements from the MSO/DPO4000B Series
is as simple as connecting a USB cable from the oscilloscope to your
PC. Key software applications – NI LabVIEW SignalExpress™ Tektronix
Edition, OpenChoice® Desktop, and Microsoft Excel and Word
toolbars – are included standard with each oscilloscope to enable
fast and easy direct communication with your Windows PC.
NI
LabVIEW SignalExpress Tektronix Edition enables you to instantly acquire,
generate, analyze, compare, import, and save measurement data and
signals using an intuitive drag-and-drop user interface that does
not require any programming. The optional Professional Version offers
over 200 built-in functions that provide additional signal processing,
advanced analysis, sweeping, and user-defined step capabilities.
For simple tasks, the included OpenChoice Desktop enables fast
and easy communication between the oscilloscope and your PC through
USB or LAN for transferring settings, waveforms, and screen images.
The LXI web interface provides access to network settings,
enables remote instrument control and is accessible from any standard
web browser.
The MSO/DPO4000B Series can also
be connected to your network using the LAN port. The included LXI
web interface provides information about the current configuration
of your MSO/DPO4000B Series oscilloscope, including network configuration.
You can make changes to the network configuration of your MSO/DPO4000B
Series oscilloscope directly from the web interface through a password-protected
web page. Additionally, the popular e*Scope® remote instrument
control is enabled on the MSO/DPO4000B Series. It continues to offer
control of instrument settings, saving of screen images and instrument
data, and saving/loading of instrument setups through a standard web
browser.
Characteristics
Vertical System Analog Channels
|
Characteristic
|
DPO4034B
MSO4034B
|
DPO4054B
MSO4054B
|
DPO4104B
MSO4104B
|
|
Input Channels
|
4
|
|
Analog Bandwidth (–3 dB) 5 mV/div - 1 V/div
|
350 MHz
|
500 MHz
|
1 GHz
|
|
Calculated Rise Time 5 mV/div (typical)
|
1 ns
|
700 ps
|
350 ps
|
|
Hardware Bandwidth Limits
|
20 MHz or 250 MHz
|
|
Input Coupling
|
AC, DC
|
|
Input Impedance
|
1 MΩ ±1%, 50 Ω ±1%
|
|
Input Sensitivity, 1 MΩ
|
1 mV/div to 10 V/div
|
|
Input Sensitivity, 50 Ω
|
1 mV/div to 1 V/div
|
|
Vertical Resolution
|
8 bits (11 bits with Hi Res)
|
|
Max Input Voltage, 1 MΩ
|
300 VRMS CAT II with peaks ≤ ±425 V
|
|
Max Input Voltage, 50 Ω
|
5 VRMS with peaks < ±20 V
|
|
DC Gain Accuracy
|
±1.5%, derated at 0.10%/°C above 30 °C
|
|
Channel-to-Channel Isolation
|
≥100:1 at ≤100 MHz and ≥30:1 at >100 MHz up to
the rated bandwidth for any two channels having equal volts/div settings
|
Offset Range
|
Range
|
1 MΩ
|
50 Ω
|
|
1 mV/div to 50 mV/div
|
±1 V
|
±1 V
|
|
50.5 mV/div to 99.5 mV/div
|
±0.5 V
|
±0.5 V
|
|
100 mV/div to 500 mV/div
|
±10 V
|
±10 V
|
|
505 mV/div to 995 mV/div
|
±5 V
|
±5 V
|
|
1 V/div to 5 V/div
|
±100 V
|
±5 V
|
|
5.05 V/div to 10 V/div
|
±50 V
|
NA
|
Vertical System Digital Channels
|
Characteristic
|
All MSO4000B Models
|
|
Input Channels
|
16 Digital (D15 - D0)
|
|
Thresholds
|
Per-channel Thresholds
|
|
Threshold Selections
|
TTL, CMOS, ECL, PECL, User Defined
|
|
User-defined Threshold Range
|
±40 V
|
|
Maximum Input Voltage
|
±42 Vpeak
|
|
Threshold Accuracy
|
±(100 mV + 3% of threshold setting)
|
|
Input Dynamic Range
|
30 Vp-p ≤200 MHz
10 Vp-p >200 MHz
|
|
Minimum Voltage Swing
|
400 mV
|
|
Input Impedance
|
100 kΩ
|
|
Probe Loading
|
3 pF
|
|
Vertical Resolution
|
1 bit
|
Horizontal System Analog Channels
|
Characteristic
|
DPO4034B
MSO4034B
|
DPO4054B
MSO4054B
|
DPO4104B
MSO4104B
|
|
Maximum Sample Rate (All channels)
|
2.5 GS/s
|
2.5 GS/s
|
5 GS/s
|
|
Maximum Record Length (All channels)
|
20M points
|
|
Maximum Duration at Highest Sample Rate (All channels)
|
8 ms
|
8 ms
|
4 ms
|
|
Time Base Range
|
1 ns to 1,000 s
|
400 ps to 1,000 s
|
|
Time Base Delay Time Range
|
–10 divisions to 5000 s
|
|
Channel-to-Channel Deskew Range
|
±125 ns
|
|
Time Base Accuracy
|
±5 ppm over any ≥1 ms interval
|
Horizontal System Digital Channels
|
Characteristic
|
All MSO4000B Models
|
|
Maximum Sample Rate (Main)
|
500 MS/s (2 ns resolution)
|
|
Maximum Record Length (Main)
|
20M points
|
|
Maximum Sample Rate (MagniVu)
|
16.5 GS/s (60.6 ps resolution)
|
|
Maximum Record Length (MagniVu)
|
10k points centered around the trigger
|
|
Minimum Detectable Pulse Width (Typical)
|
1 ns
|
|
Channel-to-Channel Skew (Typical)
|
200 ps
|
|
Maximum Input Toggle Rate
|
500 MHz
Maximum frequency sine wave that can
accurately be reproduced as a logic square wave. Requires the use
of a short ground extender on each channel.
This is
the maximum frequency at the minimum swing amplitude. Higher toggle
rates can be achieved with higher amplitudes.
|
Trigger System
|
Characteristic
|
Description
|
|
Main Trigger Modes
|
Auto, Normal, and Single
|
|
Trigger Coupling
|
DC, AC, HF reject (attenuates >50 kHz), LF reject (attenuates
<50 kHz), noise reject (reduces sensitivity)
|
|
Trigger Holdoff Range
|
20 ns to 8 s
|
Trigger Sensitivity
|
Characteristic
|
Description
|
|
Internal DC Coupled
|
|
1 MΩ Path
(All models)
50 Ω Path
(MSO/DPO4054B, MSO/DPO4034B)
|
For 1 mV/div to 4.98 mV/div; 0.75 div from DC to 50 MHz, increasing
to 1.3 div at rated bandwidth
For ≥5 mV/div; 0.4 div
from DC to 50 MHz, increasing to 1 div at rated bandwidth
|
|
50 Ω Path
(MSO/DPO4104B)
|
0.4 div from DC to 50 MHz, increasing to 1 div at rated bandwidth
|
|
External
|
|
Auxiliary Input
|
200 mV from DC to 50 MHz, increasing to 500 mV at rated bandwidth
|
Trigger Level Range
|
Characteristic
|
Description
|
|
Any Channel
|
±8 divisions from center of screen
|
|
External
(Auxiliary Input)
|
±8 V
|
Trigger Modes
|
Mode
|
Description
|
|
Edge
|
Positive or negative slope on any channel or front-panel auxiliary
input. Coupling includes DC, AC, HF reject, LF reject, and noise reject
|
|
Sequence (B-trigger)
|
Trigger Delay by Time – 4 ns to 8 s. Or Trigger Delay by Events
– 1 to 4,000,000 events
|
|
Pulse Width
|
Trigger on width of positive or negative pulses that are >,
<, =, or ≠ a specified period of time (4 ns to 8 s)
|
|
Timeout
|
Trigger when no pulse is detected within a specified time
(4 ns to 8 s)
|
|
Runt
|
Trigger on a pulse that crosses one threshold but fails to
cross a second threshold before crossing the first again
|
|
Logic
|
Trigger when any logical pattern of channels goes false or
stays true for specified period of time (4 ns to 8 s). Any input can
be used as a clock to look for the pattern on a clock edge. Pattern
(AND, OR, NAND, NOR) specified for all analog and digital input channels
defined as High, Low, or Don't Care
|
|
Setup and Hold
|
Trigger on violations of both setup time and hold time between
clock and data present on any of the input channels
|
|
Rise/Fall Time
|
Trigger on pulse edge rates that are faster or slower than
specified. Slope may be positive, negative, or either
|
|
Video
|
Trigger on all lines, odd, even, or all fields on NTSC, PAL,
and SECAM video signals
|
|
Extended Video (Optional)
|
Trigger on 480p/60, 576p/50, 720p/30, 720p/50, 720p/60, 875i/60,
1080i/50, 1080i/60, 1080p/24, 1080p/24sF, 1080p/25, 1080p/30, 1080p/50,
1080p/60, and custom bi-level and tri-level sync video standards
|
|
I2C (Optional)
|
Trigger on Start, Repeated Start, Stop, Missing ACK, Address
(7 or 10 bit), Data, or Address and Data on I2C buses up
to 10 Mb/s
|
|
SPI (Optional)
|
Trigger on SS active, MOSI, MISO, or MOSI and MISO on SPI
buses up to 50 Mb/s
|
|
USB (Optional)
|
Low-speed: Trigger on Sync, Reset, Suspend, Resume, End of
Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special
Packet, Error.
Token packet trigger – Any token type, SOF,
OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and
SETUP token types. Address can be further specified to trigger on
≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a
range. Frame number can be specified for SOF token using binary, hex,
unsigned decimal and don't care digits.
Data packet trigger
– Any data type, DATA0, DATA1; Data can be further specified to trigger
on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside
of a range.
Handshake packet trigger – Any handshake type,
ACK, NAK, STALL.
Special packet trigger – Any special type,
Reserved.
Error trigger – PID Check, CRC5 or CRC16, Bit
Stuffing.
|
|
Full-speed: Trigger on Sync, Reset, Suspend, Resume, End of
Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special
Packet, Error.
Token packet trigger – Any token type, SOF,
OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and
SETUP token types. Address can be further specified to trigger on
≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a
range. Frame number can be specified for SOF token using binary, hex,
unsigned decimal and don't care digits.
Data packet trigger
– Any data type, DATA0, DATA1; Data can be further specified to trigger
on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside
of a range.
Handshake packet trigger – Any handshake type,
ACK, NAK, STALL.
Special packet trigger – Any special type,
PRE, Reserved.
Error trigger – PID Check, CRC5 or CRC16,
Bit Stuffing.
|
|
High-speed: Trigger on Sync, Reset, Suspend, Resume, End of
Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special
Packet, Error.
Token packet trigger – Any token type, SOF,
OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and
SETUP token types. Address can be further specified to trigger on
≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a
range. Frame number can be specified for SOF token using binary, hex,
unsigned decimal and don't care digits.
Data packet trigger
– Any data type, DATA0, DATA1, DATA2, DATAM; Data can be further specified
to trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside
or outside of a range.
Handshake packet trigger – Any handshake
type, ACK, NAK, STALL, NYET.
Special packet trigger – Any
special type, ERR, SPLIT, PING, Reserved. SPLIT packet components
that can be specified include:
Hub Address
Start/Complete – Don't Care, Start (SSPLIT), Complete (CSPLIT)
Port Address
Start and End bits – Don’t
Care, Control/Bulk/Interrupt (Full-speed Device, Low-speed Device),
Isochronous (Data is Middle, Data is End, Data is Start, Data is All)
Endpoint Type – Don’t Care, Control, Isochronous, Bulk,
Interrupt
Error trigger – PID Check, CRC5 or CRC16, Any.
High-speed support only available on MSO4104B and DPO4104B
models.
|
|
Ethernet (Optional)
|
10BASE-T: Trigger on Start Frame Delimiter, MAC Addresses,
MAC Q-Tag Control Information, MAC Length/Type, IP Header, TCP Header,
TCP/IPv4/MAC Client Data, End of Packet, FCS (CRC) Error.
MAC Addresses – Trigger on Source and Destination 48-bit address
values.
MAC Q-Tag Control Information – Trigger on Q-Tag
32-bit value.
MAC Length/Type – Trigger on ≤, <, =,
>, ≥, ≠ a particular 16-bit value, or inside or outside of a range.
IP Header – Trigger on IP Protocol 8-bit value, Source Address,
Destination Address.
TCP Header – Trigger on Source Port,
Destination Port, Sequence Number, and Ack Number.
TCP/IPv4/MAC
Client Data – Trigger on ≤, <, =, >, ≥, ≠ a particular data value,
or inside or outside of a range. Selectable number of bytes to trigger
on from 1-16. Byte offset options of Don't Care, 0-1499.
|
|
100BASE-TX: Trigger on Start Frame Delimiter, MAC Addresses,
MAC Q-Tag Control Information, MAC Length/Type, IP Header, TCP Header,
TCP/IPv4/MAC Client Data, End of Packet, Idle, FCS (CRC) Error.
MAC Addresses – Trigger on Source and Destination 48-bit
address values.
MAC Q-Tag Control Information – Trigger
on Q-Tag 32-bit value.
MAC Length/Type – Trigger on ≤,
<, =, >, ≥, ≠ a particular 16-bit value, or inside or outside of
a range.
IP Header – Trigger on IP Protocol 8-bit value,
Source Address, Destination Address.
TCP Header – Trigger
on Source Port, Destination Port, Sequence Number, and Ack Number.
TCP/IPv4/MAC Client Data – Trigger on ≤, <, =, >, ≥, ≠
a particular data value, or inside or outside of a range. Selectable
number of bytes to trigger on from 1-16. Byte offset options of Don't
Care, 0-1499.
|
|
CAN (Optional)
|
Trigger on Start of Frame, Frame Type (data, remote, error,
overload), Identifier (standard or extended), Data, Identifier and
Data, End of Frame, Missing ACK, or Bit Stuffing Error on CAN signals
up to 1 Mb/s. Data can be further specified to trigger on ≤, <,
=, >, ≥, or ≠ a specific data value. User-adjustable sample point
is set to 50% by default
|
|
LIN (Optional)
|
Trigger on Sync, Identifier, Data, Identifier and Data, Wakeup
Frame, Sleep Frame, Errors such as Sync, Parity, or Checksum Errors
up to 100 Kb/s (by LIN definition, 20 Kb/s)
|
|
FlexRay (Optional)
|
Trigger on Start of Frame, Type of Frame (Normal, Payload,
Null, Sync, Startup), Identifier, Cycle Count, Complete Header Field,
Data, Identifier and Data, End of Frame or Errors such as Header CRC,
Trailer CRC, Null Frame, Sync Frame, or Startup Frame Errors up to
100 Mb/s
|
|
RS-232/422/485/UART (Optional)
|
Trigger on Tx Start Bit, Rx Start Bit, Tx End of Packet, Rx
End of Packet, Tx Data, Rx Data, Tx Parity Error, and Rx Parity Error
up to 10 Mb/s
|
|
MIL-STD-1553 (Optional)
|
Trigger on Sync, Word Type, Parity Error. Data can be further
specified to trigger on ≤, <, =, >, ≥, ≠ a specific data value,
or inside or outside of a range.
|
|
I2S/LJ/RJ/TDM (Optional)
|
Trigger on Word Select, Frame Sync, or Data. Data can be further
specified to trigger on ≤, <, =, >, ≥, ≠ a specific data value,
or inside or outside of a range
Maximum data rate for I2S/LJ/RJ is 12.5 Mb/s
Maximum data rate for TDM is 25 Mb/s
|
|
Parallel (Available on MSO models only)
|
Trigger on a parallel bus data value. Parallel bus can be
from 1 to 20 bits in size. Binary and Hex radices are supported
|
Acquisition Modes
|
Mode
|
Description
|
|
Sample
|
Acquire sampled values
|
|
Peak Detect
|
Captures glitches as narrow as 800 ps (1 GHz models) or 1.6 ns
(500 MHz and 350 MHz models) at all sweep speeds
|
|
Averaging
|
From 2 to 512 waveforms included in average
|
|
Envelope
|
Min-Max envelope reflecting Peak Detect data over multiple
acquisitions
|
|
Hi Res
|
Real-time boxcar averaging reduces random noise and increases
vertical resolution
|
|
Roll
|
Scrolls waveforms right to left across the screen at sweep
speeds slower than or equal to 40 ms/div
|
Waveform Measurements
|
Measurement
|
Description
|
|
Cursors
|
Waveform and Screen
|
|
Automatic Measurements
|
29, of which up to four can be displayed on-screen at any
one time. Measurements include: Period, Frequency, Delay, Rise Time,
Fall Time, Positive Duty Cycle, Negative Duty Cycle, Positive Pulse
Width, Negative Pulse Width, Burst Width, Phase, Positive Overshoot,
Negative Overshoot, Peak-to-Peak, Amplitude, High, Low, Max, Min,
Mean, Cycle Mean, RMS, Cycle RMS, Positive Pulse Count, Negative Pulse
Count, Rising Edge Count, Falling Edge Count, Area and Cycle Area
|
|
Measurement Statistics
|
Mean, Min, Max, Standard Deviation
|
|
Reference Levels
|
User-definable reference levels for automatic measurements
can be specified in either percent or units
|
|
Gating
|
Isolate the specific occurrence within an acquisition to take
measurements on, using either the screen or waveform cursors
|
|
Waveform Histogram
|
A waveform histogram provides an array of data values representing
the total number of hits inside of a user-defined region of the display.
A waveform histogram is both a visual graph of the hit distribution
as well as a numeric array of values that can be measured.
Sources – Channel 1, Channel 2, Channel 3, Channel 4, Ref 1, Ref
2, Ref 3, Ref 4, Math
Types – Vertical, Horizontal
|
|
Waveform Histogram Measurements
|
Waveform Count, Hits in Box, Peak Hits, Median, Max, Min,
Peak-to-Peak, Mean, Standard Deviation, Sigma 1, Sigma 2, Sigma 3
|
Waveform Math
|
Characteristic
|
Description
|
|
Arithmetic
|
Add, subtract, multiply, and divide waveforms
|
|
Math Functions
|
Integrate, Differentiate, FFT
|
|
FFT
|
Spectral magnitude
|
|
FFT Vertical Scale: Linear RMS or dBV RMS
|
|
FFT Window Settings: Rectangular, Hamming, Hanning, Blackman
Harris
|
|
Advanced Math
|
Define extensive algebraic expressions including waveforms,
reference waveforms, math functions.
Perform math on math using
complex equations (FFT, Intg, Diff, Log, Exp, Sqrt, Abs, Sine, Cosine,
Tangent, Rad, Deg), scalars, up to two user-adjustable variables and
results of parametric measurements (Period, Freq, Delay, Rise, Fall,
PosWidth, NegWidth, BurstWidth, Phase, PosDutyCycle, NegDutyCycle,
PosOverShoot, NegOverShoot, PeakPeak, Amplitude, RMS, CycleRMS, High,
Low, Max, Min, Mean, CycleMean, Area, CycleArea, and trend plots)
e.g. (Intg(Ch1–Mean(Ch1))×1.414×VAR1)
|
Power Measurements (Optional)
|
Measurement
|
Description
|
|
Power Quality Measurements
|
VRMS, VCrest Factor, Frequency, IRMS, ICrest Factor, True Power, Apparent Power,
Reactive Power, Power Factor, Phase Angle
|
|
Switching Loss Measurements
|
Power Loss: Ton, Toff, Conduction, Total
|
|
Energy Loss: Ton, Toff, Conduction,
Total
|
|
Harmonics
|
THD-F, THD-R, RMS measurements
|
|
Graphical and table displays of harmonics
|
|
Test to IEC61000-3-2 Class A and MIL-STD-1399
|
|
Ripple Measurements
|
Vripple and Iripple
|
|
Modulation Analysis
|
Graphical display of +Pulse Width, –Pulse Width, Period, Frequency,
+Duty Cycle, and –Duty Cycle modulation types
|
|
Safe Operating Area
|
Graphical display and mask testing of switching device safe
operating area measurements
|
|
dV/dt and dI/dt Measurements
|
Cursor measurements of slew rate
|
Limit/Mask Testing (Optional)
|
Characteristic
|
Description
|
|
Included Standard Masks
|
ITU-T, ANSI T1.102, USB
|
|
Test Source
|
Limit Test: Any Ch1 - Ch4 or any R1 - R4
Mask Test:
Any Ch1 - Ch4
|
|
Mask Creation
|
Limit test vertical tolerance from 0 to 1 division in 1 m
division increments; Limit test horizontal tolerance from 0 to 500 m
division in 1 m division increments
|
|
Load standard mask from internal memory
|
|
Load custom mask from text file with up to 8 segments
|
|
Mask Scaling
|
Lock to Source ON (mask automatically re-scales with source-channel
settings changes)
Lock to Source OFF (mask does not re-scale
with source-channel settings changes)
|
|
Test Criteria Run Until
|
Minimum number of waveforms (from 1 to 1,000,000; Infinity)
Minimum elapsed time (from 1 second to 48 hours; Infinity)
|
|
Violation Threshold
|
From 1 to 1,000,000
|
|
Actions on Test Failure
|
Stop acquisition, save screen image to file, save waveform
to file, print screen image, trigger out pulse, set remote interface
SRQ
|
|
Actions on Test Complete
|
Trigger out pulse, set remote interface SRQ
|
|
Results Display
|
Test status, total waveforms, number of violations, violation
rate, total tests, failed tests, test failure rate, elapsed time,
total hits for each mask segment
|
Software
|
Software
|
Description
|
|
NI LabVIEW SignalExpress Tektronix Edition
|
A fully interactive measurement software environment optimized
for the MSO/DPO4000B Series, enables you to instantly acquire, generate,
analyze, compare, import, and save measurement data and signals using
an intuitive drag-and-drop user interface that does not require any
programming.
Standard MSO/DPO4000B Series support for acquiring,
controlling, viewing, and exporting your live signal data is permanently
available through the software. The full version (SIGEXPTE) adds additional
signal processing, advanced analysis, mixed signal, sweeping, limit
testing, and user-defined step capabilities and is available for a
30-day trial period standard with each instrument.
|
|
OpenChoice® Desktop
|
Enables fast and easy communication between a Windows PC and
the MSO/DPO4000B Series, using USB or LAN. Transfer and save settings,
waveforms, measurements, and screen images. Included Word and Excel
toolbars automate the transfer of acquisition data and screen images
from the oscilloscope into Word and Excel for quick reporting or further
analysis.
|
|
IVI Driver
|
Provides a standard instrument programming interface for common
applications such as LabVIEW, LabWindows/CVI, Microsoft .NET and MATLAB.
|
|
e*Scope®
|
Enables control of the MSO/DPO4000B Series over a network
connection through a standard web browser. Simply enter the IP address
or network name of the oscilloscope followed by :81 (to represent
connecting through Port 81) and a web page will be served to the browser
|
|
LXI Class C
Web Interface
|
Connect to the MSO/DPO4000B Series through a standard web
browser by simply entering the oscilloscope's IP address or network
name in the address bar of the browser. The web interface enables
viewing of instrument status and configuration, and status and modification
of network settings. All web interaction conforms to LXI Class C specification.
|
Display Characteristics
|
Characteristic
|
Description
|
|
Display Type
|
10.4 in. (264 mm) liquid-crystal TFT color display
|
|
Display Resolution
|
1,024 horizontal × 768 vertical pixels (XGA)
|
|
Waveform Styles
|
Vectors, Dots, Variable Persistence, Infinite Persistence
|
|
Graticules
|
Full, Grid, Solid, Cross Hair, Frame, IRE, and mV
|
|
Format
|
YT and simultaneous XY/YT
|
|
Waveform Capture Rate
|
>50,000 wfm/s maximum
|
Input/Output Ports
|
Port
|
Description
|
|
USB 2.0 High-speed Host Port
|
Supports USB mass storage devices, printers and keyboard.
Two ports on front and two ports on rear of instrument
|
|
USB 2.0 Device Port
|
Rear-panel connector allows for communication/control of oscilloscope
through USBTMC or GPIB (with a TEK-USB-488), and direct printing to
all PictBridge-compatible printers
|
|
LAN Port
|
RJ-45 connector, supports 10/100/1000 Mb/s
|
|
XGA Video Port
|
DB-15 female connector, connect to show the oscilloscope display
on an external monitor or projector
|
|
Auxiliary Input
|
Front-panel BNC connector. Input Impedance 1 MΩ. Max input
300 VRMS CAT II with peaks ≤ ±425 V
|
|
Probe Compensator Output
|
Front-panel pins
Amplitude: 2.5 V
Frequency:
1 kHz
|
|
Auxiliary Out
|
Rear-panel BNC connector
VOUT (Hi): ≥2.5 V
open circuit, ≥1.0 V 50 Ω to ground
VOUT (Lo): ≤0.7 V
into a load of ≤4 mA; ≤0.25 V 50 Ω to ground
Output
can be configured to provide a pulse out signal when the oscilloscope
triggers, the internal oscilloscope reference clock out, or an event
out for limit/mask testing
|
|
External Reference In
|
Time-base system can phase lock to an external 10 MHz reference
(10 MHz ±1%)
|
|
Kensington Lock
|
Rear-panel security slot connects to standard Kensington lock
|
LAN eXtensions for Instrumentation (LXI)
|
Characteristic
|
Description
|
|
Class
|
LXI Class C
|
|
Version
|
V1.3
|
Power Source
|
Characteristic
|
Description
|
|
Power Source Voltage
|
100 to 240 V ±10%
|
|
Power Source Frequency
|
45 to 66 Hz (85 to 264 V)
360 to 440 Hz (100 to 132 V)
|
|
Power Consumption
|
225 W maximum
|
Physical Characteristics
|
Dimensions
|
mm
|
in.
|
|
Height
|
229
|
9.0
|
|
Width
|
439
|
17.3
|
|
Depth
|
147
|
5.8
|
|
Weight
|
kg
|
lb.
|
|
Net
|
5
|
11
|
|
Shipping
|
10.7
|
23.6
|
|
Rackmount Configuration
|
5U
|
|
Cooling Clearance
|
2 in. (51 mm) required on left side and rear of
instrument
|
|
VESA Mount
|
Standard (MIS-D 100) 100 mm VESA mounting points
on rear of instrument
|
Environmental
|
Characteristic
|
Description
|
|
Temperature
|
|
Operating
|
0 ºC to +50 ºC
|
|
Nonoperating
|
–20 ºC to +60 ºC
|
|
Humidity
|
|
Operating
|
High: 40 ºC to 50 ºC, 10% to 60% Relative Humidity
Low: 0 ºC to 40 ºC, 10% to 90% Relative Humidity
|
|
Nonoperating
|
High: 40 ºC to 60 ºC, 5% to 60% Relative Humidity
Low:
0 ºC to 40 ºC, 5% to 90% Relative Humidity
|
|
Altitude
|
|
Operating
|
9,843 ft. (3,000 m)
|
|
Nonoperating
|
30,000 ft. (9,144 m)
|
|
Regulatory
|
|
Electromagnetic Compatibility
|
EC Council Directive 2004/108/EC
|
|
Safety
|
UL61010-1, Second Edition; CSA61010-1 Second Edition, EN61010-1:2001;
IEC 61010-1:2001
|
Ordering Information
MSO/DPO4000B Family
|
Model
|
Description
|
|
DPO4000B Models
|
|
DPO4034B
|
350 MHz, 2.5 GS/s, 20M record length,
4-channel digital
phosphor oscilloscope
|
|
DPO4054B
|
500 MHz, 2.5 GS/s, 20M record length,
4-channel digital
phosphor oscilloscope
|
|
DPO4104B
|
1 GHz, 5 GS/s, 20M record length,
4-channel digital
phosphor oscilloscope
|
|
MSO4000B Models
|
|
MSO4034B
|
350 MHz, 2.5 GS/s, 20M record length,
4+16 channel
mixed signal oscilloscope
|
|
MSO4054B
|
500 MHz, 2.5 GS/s, 20M record length,
4+16 channel
mixed signal oscilloscope
|
|
MSO4104B
|
1 GHz, 5 GS/s, 20M record length,
4+16 channel mixed
signal oscilloscope
|
All Models Include: One
passive voltage probe per analog channel (TPP0500 500 MHz, 10X, 3.9 pF
for 500 MHz and 350 MHz models; TPP1000 1 GHz, 10X, 3.9 pF for 1 GHz
models), Front Cover (200-5130-xx), User Manual (071-2810-xx), Documentation
CD (063-4300-xx), OpenChoice® Desktop Software, NI LabVIEW
SignalExpress™ Tektronix Edition Software, Calibration Certificates
document measurement traceability to National Metrology Institute(s)
– the Quality System this product is manufactured in is ISO9001 registered,
power cord, accessory bag (016-2029-xx) and a three-year warranty.
Please specify power plug and manual language version when ordering.
MSO Models also Include: One P6616 16-channel
logic probe and a logic probe accessory kit (020-2662-xx).
Application Modules
|
Module
|
Description
|
|
DPO4AERO
|
Aerospace Serial Triggering and Analysis Module. Enables triggering
on packet-level information on MIL-STD-1553 buses as well as analytical
tools such as digital views of the signal, bus views, packet decoding,
search tools, and packet decode tables with time-stamp information.
Signal Inputs – Any Ch1 - Ch4 (and any D0 - D15 on MSO models)
Recommended Probing – Single ended
|
|
DPO4AUDIO
|
Audio Serial Triggering and Analysis Module. Enables triggering
on packet-level information on I2S, LJ, RJ, and TDM audio
buses as well as analytical tools such as digital views of the signal,
bus views, packet decoding, search tools, and packet decode tables
with time-stamp information.
Signal Inputs – Any Ch1 - Ch4
(and any D0 - D15 on MSO models)
Recommended Probing – I2S, LJ, RJ, TDM: Single ended
|
|
DPO4AUTO
|
Automotive Serial Triggering and Analysis Module. Enables
triggering on packet-level information on CAN and LIN buses as well
as analytical tools such as digital views of the signal, bus views,
packet decoding, search tools, and packet decode tables with time-stamp
information.
Signal Inputs – LIN: Any Ch1 - Ch4 (and any D0
- D15 on MSO models); CAN: Any Ch1 - Ch4 (and any D0 - D15 on MSO
models), single-ended probing only
Recommended Probing – LIN:
Single ended; CAN: Single ended or differential
|
|
DPO4AUTOMAX
|
Extended Automotive Serial Triggering and Analysis Module.
Enables triggering on packet-level information on CAN, LIN, and FlexRay
buses as well as analytical tools such as digital views of the signal,
bus views, packet decoding, search tools, packet decode tables with
time-stamp information, and eye diagram analysis software.
Signal Inputs – LIN: Any Ch1 - Ch4 (and any D0 - D15 on MSO models);
CAN: Any Ch1 - Ch4 (and any D0 - D15 on MSO models), single-ended
probing only; FlexRay: Any Ch1 - Ch4 (and any D0 - D15 on MSO models),
single-ended probing only
Recommended Probing – LIN: Single
ended; CAN, FlexRay: Single ended or differential
|
|
DPO4COMP
|
Computer Serial Triggering and Analysis Module. Enables triggering
on packet-level information on RS-232/422/485/UART buses as well as
analytical tools such as digital views of the signal, bus views, packet
decoding, search tools, and packet decode tables with time-stamp information.
Signal Inputs – Any Ch1 - Ch4 (and any D0 - D15 on MSO models),
single-ended probing only
Recommended Probing – RS-232/UART:
Single ended; RS-422/485: Differential
|
|
DPO4EMBD
|
Embedded Serial Triggering and Analysis Module. Enables triggering
on packet-level information on I2C and SPI buses as well
as analytical tools such as digital views of the signal, bus views,
packet decoding, search tools, and packet decode tables with time-stamp
information.
Signal Inputs – I2C: Any Ch1 - Ch4
(and any D0 - D15 on MSO models); SPI: Any Ch1 - Ch4 (and any D0 -
D15 on MSO models)
Recommended Probing – I2C, SPI:
Single ended
|
|
DPO4ENET
|
Ethernet Serial Triggering and Analysis Module. Enables triggering
on packet-level information on 10BASE-T and 100BASE-TX buses as well
as analytical tools such as digital views of the signal, bus views,
packet decoding, search tools, and packet decode tables with time-stamp
information.
Signal Inputs – Any Ch1 - Ch4
Recommended
Probing – 10BASE-T: Single ended or differential; 100BASE-TX: Differential
|
|
DPO4USB
|
USB Serial Triggering and Analysis Module. Enables triggering
on packet-level content for low-speed, full-speed, and high-speed
USB serial buses. Also enables analytical tools such as digital views
of the signal, bus views, packet decoding, search tools, and packet
decode tables with time-stamp information for low-speed, full-speed,
and high-speed USB serial buses.
Signal Inputs – Low-speed
and Full-speed: Any Ch1 - Ch4 (and any D0 - D15 on MSO models) for
single ended, Any Ch1 - Ch4 for differential; High-speed: Any Ch1
- Ch4
Recommended Probing – Low-speed and Full-speed: Single
ended or differential; High-speed: Differential
USB high-speed
supported only on MSO4104B and DPO4104B models
|
|
DPO4PWR
|
Power Analysis Application Module. Enables quick and accurate
analysis of power quality, switching loss, harmonics, safe operating
area (SOA), modulation, ripple, and slew rate (dI/dt, dV/dt)
|
|
DPO4LMT
|
Limit and Mask Testing Application Module. Enables testing
against limit templates generated from "golden" waveforms and mask
testing using custom or standard telecommunications or computer masks
|
|
DPO4VID
|
HDTV and Custom (nonstandard) Video Triggering Module
|
Instrument Options
Power Plug Options
|
Option
|
Description
|
|
Opt. A0
|
North America
|
|
Opt. A1
|
Universal Euro
|
|
Opt. A2
|
United Kingdom
|
|
Opt. A3
|
Australia
|
|
Opt. A5
|
Switzerland
|
|
Opt. A6
|
Japan
|
|
Opt. A10
|
China
|
|
Opt. A11
|
India
|
|
Opt. A99
|
No power cord or AC adapter
|
Language Options*1
|
Option
|
Description
|
|
Opt. L0
|
English manual
|
|
Opt. L1
|
French manual
|
|
Opt. L2
|
Italian manual
|
|
Opt. L3
|
German manual
|
|
Opt. L4
|
Spanish manual
|
|
Opt. L5
|
Japanese manual
|
|
Opt. L6
|
Portuguese manual
|
|
Opt. L7
|
Simplified Chinese manual
|
|
Opt. L8
|
Traditional Chinese manual
|
|
Opt. L9
|
Korean manual
|
|
Opt. L10
|
Russian manual
|
|
Opt. L99
|
No manual
|
*1 Language options include a translated
front-panel overlay for the selected language(s).
Service
Options*2
|
Option
|
Description
|
|
Opt. CA1
|
Provides a single calibration event, or coverage for the designated
calibration interval, whichever comes first.
|
|
Opt. C3
|
Calibration Service 3 years
|
|
Opt. C5
|
Calibration Service 5 years
|
|
Opt. D1
|
Calibration Data Report
|
|
Opt. D3
|
Calibration Data Report 3 years (with Opt. C3)
|
|
Opt. D5
|
Calibration Data Report 5 Years (with Opt. C5)
|
|
Opt. R5
|
Repair Service 5 years (including warranty)
|
*2 Probes and accessories are not covered
by the oscilloscope warranty and service offerings. Refer to the datasheet
of each probe and accessory model for its unique warranty and calibration
terms.
Recommended Probes
|
Probe
|
Description
|
|
Tektronix offers over 100 different probes to
meet your application needs. For a comprehensive listing of available
probes, please visit www.tektronix.com/probes.
|
|
TPP0500
|
500 MHz, 10X TekVPI® passive voltage probe with
3.9 pF input capacitance
|
|
TPP1000
|
1 GHz, 10X TekVPI passive voltage probe with 3.9 pF input
capacitance
|
|
TAP1500
|
1.5 GHz TekVPI active single-ended voltage probe
|
|
TDP1500
|
1.5 GHz TekVPI differential voltage probe with ±25 V differential
input voltage
|
|
TDP1000
|
1 GHz TekVPI differential voltage probe with ±42 V differential
input voltage
|
|
TDP0500
|
500 MHz TekVPI differential voltage probe with ±42 V differential
input voltage
|
|
TCP0150
|
20 MHz TekVPI 150 Ampere AC/DC current probe
|
|
TCP0030
|
120 MHz TekVPI 30 Ampere AC/DC current probe
|
|
P5200
|
1.3 kV, 25 MHz high-voltage differential probe
|
|
P5205*3
|
1.3 kV, 100 MHz high-voltage differential probe
|
|
P5210*3
|
5.6 kV, 50 MHz high-voltage differential probe
|
|
P5100
|
2.5 kV, 100X high-voltage passive probe
|
*3 Requires TekVPI® to TekProbe
BNC adapter (TPA-BNC).
Recommended Accessories
|
Accessory
|
Description
|
|
077-0512-xx
|
Service Manual (English only)
|
|
SIGEXPTE
|
NI LabVIEW SignalExpress™ Tektronix Edition Software (Full
Version)
|
|
FPGAView-xx
|
MSO Support for Altera and Xilinx FPGAs
|
|
TPA-BNC
|
TekVPI-to-TekProbe BNC Adapter
|
|
TEK-USB-488
|
GPIB-to-USB Adapter
|
|
ACD4000B
|
Soft Transit Case
|
|
HCTEK54
|
Hard Transit Case (Requires ACD4000B)
|
|
RMD5000
|
Rackmount Kit
|
|
TEK-DPG
|
Deskew Pulse Generator
|
|
067-1686-xx
|
Deskew Fixture
|
Warranty
Three-year warranty covering
all parts and labor, excluding probes.
|
|
Product(s) are manufactured in ISO registered facilities.
|
|
Product(s) complies with IEEE Standard 488.1-1987, RS-232-C,
and with Tektronix Standard Codes and Formats.
|
3GI-20156-9, 07-DEC-2010
|
|
